---------------------------------------------------------------------- (c)Kalok Corporation K-Board BBS 408-734-4258 300-14400 Baud, 8-N-1 ---------------------------------------------------------------------- Kalok KL343 - 3.5-inch 42Mbyte AT Interface Hard Drive ======================================================== JUMPER SETTINGS AND CMOS SETUP ----------------------------- ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ TOP OF DRIVE ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ ³ ³ ³ ³ Octagon KL343 ³ ³ ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍPCBÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ ÚÄÄÄÄÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄ¿ ³ o o o o 1 ³ ³ ....... 40-pin IDE connector ..... 1 ³ +5v³ O ³ ³ o o o o o ³ ³ 40.................................. ³ 0v³ O ³ ÀÄÄÄÄÄÄÄÄÄÄÄÙ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ 0v³ O ³ ³ ³ ³ ³ ³ +12v³ O ³ ³ ³ ³ ³ À r/t ÀÄÄÄÄÄÙ ³ ³ ³ ÀÄÄ st ³ ³ ÀÄÄÄÄ MASTER ³ ÀÄÄÄÄÄÄ SLAVE ÀÄÄÄÄÄÄÄÄ not connected ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ single drive ³ NO JUMPERS ³ pins 7-9 ³ ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ dual drive (primary) ³ MASTER ONLY ³ pins 5-6 ³ ³ dual drive (second) ³ SLAVE ONLY ³ pins 7-8 ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ LOGICAL PARAMETERS ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» ³ST and R/T are used for tests³ º Cyls Heads Sect/ Land {drive}º ³during manufacturing and test³ º trk zone {type }º ³These jumpers should NOT be ³ º 977 5 17 977 { 17 }º ³installed. ³ ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ Write precompensation is not required Specifications -------------- InterfaceÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ATA/IDE Capacity UnformattedÄÄÄÄÄÄÄÄ 48.07 megabytes FormattedÄÄÄÄÄÄÄÄÄÄ 42.54 megabytes Logical Parameters CylindersÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 977 Sectors/trackÄÄÄÄÄÄÄÄÄÄ 17 HeadsÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 5 Average Seek TimeÄÄÄÄÄÄÄÄÄÄÄ 33 msec Average latencyÄÄÄÄÄÄÄÄÄÄÄÄÄ 8.89 msec Rotational speedÄÄÄÄÄÄÄÄÄÄÄÄ 3375 rpm Data throughput: Maximum internalÄÄÄÄÄÄÄÄ 8.0 mb/sec. Burst rateÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 4.5 mb sec. Buffer sizeÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 8 KB Recording codeÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 2,7 RLL InterleaveÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 1:1 Acoustical noiseÄÄÄÄÄÄÄÄÄÄÄÄ 40 dBA @ 1 meter TemperatureÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 10 to 55 C operating ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ -40 to 60 C nonoperating ShockÄÄÄÂÄoperatingÄÄÄÄÄÄÄÄÄ 8 G ÀÄnon operatingÄÄÄÄÄ 40 G Mean time between failuresÄÄ 40,000 hours Power dissipationÄÄÄÄÄÄÄÄÄÄÄ 10.4 Watts Active, 8.2 Watts idle Dimensions, HxWxLÄÄÄÄÄÄÄÄÄÄÄ 1.625 x 4.00 x 5.75 inchs WeightÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 1.6 pounds(0.73 Kg.) For further installation details and full product specifications please refer to the full KL343 manual KL343.MAN ========================================================================== ---------------------------------------------------------------------- (c)Kalok Corporation K-Board BBS 408-734-4258 300-14400 Baud, 8-N-1 ---------------------------------------------------------------------- Kalok KL3100 - 3.5-inch 105Mbyte AT Interface Hard Drive ======================================================== JUMPER SETTINGS AND CMOS SETUP ----------------------------- ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ TOP OF DRIVE ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ ³ ³ ³ ³ Octagon KL3100 ³ ³ ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍPCBÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ ÚÄÄÄÄÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ o o o o 1 ³ ³ ....... 40-pin IDE connector ..... 1 ³ ³ O O O O ³ ³ o o o o o ³ ³ 40.................................. ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÙ ÀÄÄÄÄÄÄÄÄÄÄÄÙ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ +5v À0vÙ +12v ³ ³ ³ ³ ³ ³ ³ ³ ³ À r/t ³ ³ ³ ÀÄÄ st ³ ³ ÀÄÄÄÄ MASTER ³ ÀÄÄÄÄÄÄ SLAVE ÀÄÄÄÄÄÄÄÄ not connected ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ single drive ³ NO JUMPERS ³ pins 7-9 ³ ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ dual drive (primary) ³ MASTER ONLY ³ pins 5-6 ³ ³ dual drive (second) ³ SLAVE ONLY ³ pins 7-8 ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ LOGICAL PARAMETERS ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» ³ST and R/T are used for tests³ º Cyls Heads Sect/ Land º ³during manufacturing and test³ º trk zone º ³These jumpers should NOT be ³ º 979 6 35 979 º ³installed. ³ ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ Write precompensation is not required Specifications -------------- InterfaceÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ATA/IDE Capacity UnformattedÄÄÄÄÄÄÄÄ 120.34 megabytes FormattedÄÄÄÄÄÄÄÄÄÄ 105.2 megabytes Logical Parameters CylindersÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 979 Sectors/trackÄÄÄÄÄÄÄÄÄÄ 35 HeadsÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 6 Average Seek TimeÄÄÄÄÄÄÄÄÄÄÄ 19.5 msec Average latencyÄÄÄÄÄÄÄÄÄÄÄÄÄ 8.19 msec Rotational speedÄÄÄÄÄÄÄÄÄÄÄÄ 3662 rpm Data throughput: Maximum internalÄÄÄÄÄÄÄÄ 10.0 and 13.5 mb/sec. Burst rateÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 4.5 mb sec. Buffer sizeÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 32 KB Recording codeÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 2,7 RLL InterleaveÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 1:1 Acoustical noiseÄÄÄÄÄÄÄÄÄÄÄÄ 40 dBA @ 1 meter TemperatureÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 10 to 55 C operating ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ -40 to 60 C nonoperating ShockÄÄÄÂÄoperatingÄÄÄÄÄÄÄÄÄ 10 G ÀÄnon operatingÄÄÄÄÄ 60 G Mean time between failuresÄÄ 100,000 hours Power dissipationÄÄÄÄÄÄÄÄÄÄÄ 10.4 Watts Active, 8.2 Watts idle Dimensions, HxWxLÄÄÄÄÄÄÄÄÄÄÄ 1.625 x 4.00 x 5.75 inchs WeightÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 1.7 pounds(0.77 Kg.) For further installation details and full product specifications please refer to the full KL3100 manual KL3100.MAN ========================================================================== ---------------------------------------------------------------------- (c)Kalok Corporation K-Board BBS 408-734-4258 300-14400 Baud, 8-N-1 ---------------------------------------------------------------------- Kalok KL3120 - 3.5-inch 120Mbyte AT Interface Hard Drive ======================================================== JUMPER SETTINGS AND CMOS SETUP ----------------------------- ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ TOP OF DRIVE ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ ³ ³ ³ ³ Octagon KL3120 ³ ³ ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍPCBÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ ÚÄÄÄÄÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ o o o o 1 ³ ³ ....... 40-pin IDE connector ..... 1 ³ ³ O O O O ³ ³ o o o o o ³ ³ 40.................................. ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÙ ÀÄÄÄÄÄÄÄÄÄÄÄÙ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ +5v À0vÙ +12v ³ ³ ³ ³ ³ ³ ³ ³ ³ À r/t ³ ³ ³ ÀÄÄ st ³ ³ ÀÄÄÄÄ MASTER ³ ÀÄÄÄÄÄÄ SLAVE ÀÄÄÄÄÄÄÄÄ not connected ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ single drive ³ NO JUMPERS ³ pins 7-9 ³ ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ dual drive (primary) ³ MASTER ONLY ³ pins 5-6 ³ ³ dual drive (second) ³ SLAVE ONLY ³ pins 7-8 ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ LOGICAL PARAMETERS ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» ³ST and R/T are used for tests³ º Cyls Heads Sect/ Land º ³during manufacturing and test³ º trk zone º ³These jumpers should NOT be ³ º 979 6 40 981 º ³installed. ³ ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ Write precompensation is not required Specifications -------------- InterfaceÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ATA/IDE Capacity UnformattedÄÄÄÄÄÄÄÄ 137.5 megabytes FormattedÄÄÄÄÄÄÄÄÄÄ 120.6 megabytes Logical Parameters CylindersÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 981 Sectors/trackÄÄÄÄÄÄÄÄÄÄ 40 HeadsÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 6 Average Seek TimeÄÄÄÄÄÄÄÄÄÄÄ 19.5 msec Average latencyÄÄÄÄÄÄÄÄÄÄÄÄÄ 8.19 msec Rotational speedÄÄÄÄÄÄÄÄÄÄÄÄ 3662 rpm Data throughput: Maximum internalÄÄÄÄÄÄÄÄ 10.0 and 15.5 mb/sec. Burst rateÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 5 mb sec. Buffer sizeÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 32 KB Recording codeÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 2,7 RLL InterleaveÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 1:1 Acoustical noiseÄÄÄÄÄÄÄÄÄÄÄÄ 40 dBA @ 1 meter TemperatureÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 10 to 55 C operating ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ -40 to 60 C nonoperating ShockÄÄÄÂÄoperatingÄÄÄÄÄÄÄÄÄ 10 G ÀÄnon operatingÄÄÄÄÄ 60 G Mean time between failuresÄÄ 100,000 hours Power dissipationÄÄÄÄÄÄÄÄÄÄÄ 10.4 Watts Active, 8.2 Watts idle Dimensions, HxWxLÄÄÄÄÄÄÄÄÄÄÄ 1.625 x 4.00 x 5.75 inchs WeightÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 1.7 pounds(0.77 Kg.) For further installation details and full product specifications please refer to the full KL3120 manual KL3120.MAN ==========================================================================