---------------------------------------------------------------------- Contents: 26/03/1993 17:38 4,615 2105A.TXT 16/03/1993 17:59 6,095 2112A.TXT 08/07/1993 23:11 4,914 2205A.TXT 11/08/1993 16:13 6,141 2210A.TXT 08/07/1993 23:31 6,141 2217A.TXT ---------------------------------------------------------------------- MICROPOLIS 2105A DISK DRIVE SPECIFICATIONS Model Number Unformatted Capacity: 2105-15 Total Mbytes --------------- 650 ----------------- Disk Platters ----------------- 5 ----------------- Read/Write Heads ----------------- 8 ----------------- Cylinders --------------- 1760 ----------------- Bytes per track ----------- VARIABLE ----------------- Formatted Capacity Total Mbytes ---------------- 560 ----------------- Bytes per Sector ---------------- 512 ----------------- Sectors per Track ----------- VARIABLE ----------------- Performance Specifications Seek Time Adjacent Track 1.5 msec (including settling time) Average 10.0 msec Maximum 25 msec Average Rotational Latency 5.56 msec Rotational Speed 5400 rpm +/- 0.5% Data Transfer Rate at Interface Up to 5.6 Mbytes/sec Internal Data Rate 24 to 40 MHz MTBF 300,000 hours Positioner Fully balanced rotary voice coil Parking Automatic park and lock General Functional Specifications Interface AT/IDE Supports Full Common Command Set YES Mounting Plane Any orientation Power Requirements +12V +/-5% 0.75A Avg (2.0 max during start-up) +5V +/-5% 1.0A avg Power dissipation, typical 11.5 Watts 7. Drive Options ____ _______________________ ________ | J2 | | J1 | | J3 | | |_|_______________________|_|________| | | | RESERVED | | | | | | | : : : : : | | | | | | W1 | | | W2 | | | \/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/ /\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\ | LED | |________||_______________________________| W1, W2 Jumpers (Master / Slave Selection) The interface allows up to two drives (a Master and one Slave) to be attached to the AT/IDE bus. The following table shows the configurations. W1 W2 Description +------+------+-------------------------------------------------------+ | OUT | IN | Drive is Master, Slave is present | +------+------+-------------------------------------------------------+ | IN | OUT | Drive Slave | +------+------+-------------------------------------------------------+ | OUT | OUT | Drive is Master | +------+------+-------------------------------------------------------+ DRIVE IS MASTER, SLAVE IS PRESENT Specifies the Master drive (Drive 0) when two 2105A drives are used in the system. The other drive is the Slave. DRIVE IS SLAVE Specifies the Slave drive (Drive 1) when two 2105A drives are used in the system. The other drive is the Master. DRIVE IS MASTER Specifies the Master drive (DRIVE 0) when one 2105A drive is used in a system. CMOS SETUP To configure this drive on a standard CMOS set your user definable drive type to: 1024 logical cylinders, 16 logical heads, and 63 logical sectors. This setting yields 528,482,304 bytes. NOTE: If you BIOS or operating system can address over 1024 cylinders, you may set the drive up as: 1084 logical cylinders, 16 logical heads, and 63 logical sectors. This setting yields 559,448,064 bytes. ---------------------------------------------------------------------- MICROPOLIS 2112A DISK DRIVE SPECIFICATIONS Model Number Unformatted Capacity: 2112A-15 Total Mbytes -------------- 1220 ----------------- Disk Platters ----------------- 8 ----------------- Read/Write Heads ----------------- 15 ----------------- Cylinders --------------- 1760 ----------------- Bytes per track ----------- VARIABLE ----------------- Formatted Capacity Total Mbytes --------------- 1050 ----------------- Bytes per Sector ---------------- 512 ----------------- Sectors per Track ----------- VARIABLE ----------------- Performance Specifications Seek Time Adjacent Track 1.5 msec (including settling time) Average 10.0 msec Maximum 25 msec Average Rotational Latency 5.56 msec Rotational Speed 5400 rpm +/- 0.5% Data Transfer Rate at Interface Up to 5.6 Mbytes/sec Internal Data Rate 24 to 40 MHz MTBF 300,000 hours Positioner Fully balanced rotary voice coil Parking Automatic park and lock General Functional Specifications Interface AT/IDE Supports Full Common Command Set YES Mounting Plane Any orientation Power Requirements +12V +/-5% 0.75A Avg (2.0 max during start-up) +5V +/-5% 1.0A avg Power dissipation, typical 11.5 Watts 7. Drive Options ____ _______________________ ________ | J2 | | J1 | | J3 | | |_|_______________________|_|________| | | | RESERVED | | | | | | | : : : : : | | | | | | W1 | | | W2 | | | \/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/ /\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\ | LED | |________||_______________________________| W1, W2 Jumpers (Master / Slave Selection) The interface allows up to two drives (a Master and one Slave) to be attached to the AT/IDE bus. The following table shows the configurations. W1 W2 Description +------+------+-------------------------------------------------------+ | IN | IN | Drive emulates *both* Master and Slave (DEFAULT) | +------+------+-------------------------------------------------------+ | OUT | IN | Drive is Master, Slave is present | +------+------+-------------------------------------------------------+ | IN | OUT | Drive Slave | +------+------+-------------------------------------------------------+ | OUT | OUT | Drive is Master | +------+------+-------------------------------------------------------+ DRIVE EMULATES BOTH MASTER AND SLAVE Specifies that one 2112A drive can emulate both the Master drive (Drive 0) and the Slave drive (Drive 1). This option allows for existing host systems to utilize the full capacity of the drive. When the drive is configured as both the Master and the Slave, the Master's (Drive 0) capacity is set to: 1024 logical cylinders, 16 logical heads, and 63 logical sectors. This setting yields 528,482,304 bytes. The Slave's (Drive 1) capacity is set to the remaining storage on the disk drive. For this configuration, the recommended drive type setting in your computer's CMOS memory is as follows: Drive 0 Drive 1 Logical Cylinders: 1024 1010 Logical Heads: 16 16 Logical Sectors: 63 63 NOTE: The capacity of the 2112A drive may exceed the capacity that the host can access. This limitation stems from the communication link between the DOS and the BIOS. A typical limit is: 1024 cylinders 16 heads 63 sectors For optimum use of the following options, the BIOS may need to be modified. DRIVE IS MASTER, SLAVE IS PRESENT Specifies the Master drive (Drive 0) when two 2112A drives are used in the system. The other drive is the Slave. DRIVE IS SLAVE Specifies the Slave drive (Drive 1) when two 2112A drives are used in the system. The other drive is the Master. NOTE: If you have a machine with a BIOS that supports over 16 heads, you can get the drive to work as one full partition. To do this, set the drive for: 991 cylinders 64 heads 32 sectors DRIVE IS MASTER Specifies the Master drive (DRIVE 0) when one 2112A drive is used in a system. NOTE: If you have a machine with a BIOS that supports over 16 heads, you can get the drive to work as one full partition. To do this, set the drive for: 991 cylinders 64 heads 32 sectors ---------------------------------------------------------------------- MICROPOLIS 2205A DISK DRIVE SPECIFICATIONS Model Number Unformatted Capacity: 2205-15 Total Mbytes --------------- 632 ----------------- Disk Platters ----------------- 3 ----------------- Read/Write Heads ----------------- 5 ----------------- Cylinders -------------- 2372 ----------------- Bytes per track ----------- VARIABLE ----------------- Formatted Capacity Total Mbytes ---------------- 542 ----------------- Bytes per Sector ---------------- 512 ----------------- Sectors per Track ----------- VARIABLE ----------------- Performance Specifications Seek Time Track-to-Track 2 msec (including settling time) Average 10.0 msec Maximum 25 msec Average Rotational Latency 5.56 msec Rotational Speed 5400 rpm +/- 0.5% Data Transfer Rate at Interface Up to 5.0 Mbytes/sec Internal Data Rate 32 to 40 MHz MTBF 300,000 hours Positioner Fully balanced rotary voice coil Parking Automatic park and lock General Functional Specifications Interface AT/IDE Supports Full Common Command Set YES Mounting Plane Any orientation Power Requirements +12V +/-5% 0.60 Avg (2.0 max during start-up) +5V +/-5% 0.85A avg Power dissipation, typical 11.5 Watts 7. Drive Options ____ _______________________ ________ | J2 | | J1 | | J3 | | |_|_______________________|_|________| | | | RESERVED | | | | | | | : : : : : | | | | | | W1 | | | W2 | | | \/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/ /\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\ | LED | |________||_______________________________| W1, W2 Jumpers (Master / Slave Selection) The interface allows up to two drives (a Master and one Slave) to be attached to the AT/IDE bus. The following table shows the configurations. W1 W2 Description +------+------+-------------------------------------------------------+ | OUT | IN | Drive is Master, Slave is present | +------+------+-------------------------------------------------------+ | IN | OUT | Drive Slave | +------+------+-------------------------------------------------------+ | OUT | OUT | Drive is Master | +------+------+-------------------------------------------------------+ DRIVE IS MASTER, SLAVE IS PRESENT Specifies the Master drive (Drive 0) when two 2205A drives are used in the system. The other drive is the Slave. DRIVE IS SLAVE Specifies the Slave drive (Drive 1) when two 2205A drives are used in the system. The other drive is the Master. DRIVE IS MASTER Specifies the Master drive (DRIVE 0) when one 2205A drive is used in a system. CMOS SETUP To configure this drive on a standard CMOS set your user definable drive type to: 1024 logical cylinders, 16 logical heads, and 63 logical sectors. This setting yields 528,482,304 bytes. NOTE: If your BIOS or operating system can address over 1024 cylinders, you may set the drive up as: 1050 logical cylinders, 16 logical heads, and 63 logical sectors. This setting yields 541,900,800 bytes If your BIOS or operating system cannot address over 1024 cylinders, but can support over 16 heads, you may set the drive up as: 516 logical cylinders, 64 logical heads, and 32 logical sectors.. This setting yields 541,065,216 bytes. ---------------------------------------------------------------------- MICROPOLIS 2210A DISK DRIVE SPECIFICATIONS Model Number Unformatted Capacity: 2210A-5 Total Mbytes -------------- 1138 ----------------- Disk Platters ----------------- 5 ----------------- Read/Write Heads ----------------- 9 ----------------- Cylinders -------------- 2372 ----------------- Bytes per track ----------- VARIABLE ----------------- Formatted Capacity Total Mbytes --------------- 976 ----------------- Bytes per Sector ---------------- 512 ----------------- Sectors per Track ----------- VARIABLE ----------------- Performance Specifications Seek Time Track-to-Track 2 msec (including settling time) Average 10.0 msec Maximum 25 msec Average Rotational Latency 5.56 msec Rotational Speed 5400 rpm +/- 0.5% Data Transfer Rate at Interface Up to 5.0 Mbytes/sec Internal Data Rate 32 to 40 MHz MTBF 300,000 hours Positioner Fully balanced rotary voice coil Parking Automatic park and lock General Functional Specifications Interface AT/IDE Supports Full Common Command Set YES Mounting Plane Any orientation Power Requirements +12V +/-5% 0 .6A Avg (2.2A max during start-up) +5V +/-5% 0.85A avg Power dissipation, typical 11.5 Watts 7. Drive Options ____ _______________________ ________ | J2 | | J1 | | J3 | | |_|_______________________|_|________| | | | RESERVED | | | | | | | : : : : : | | | | | | W1 | | | W2 | | | \/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/ /\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\ | LED | |________||_______________________________| W1, W2 Jumpers (Master / Slave Selection) The interface allows up to two drives (a Master and one Slave) to be attached to the AT/IDE bus. The following table shows the configurations. W1 W2 Description +------+------+-------------------------------------------------------+ | IN | IN | Drive emulates *both* Master and Slave (DEFAULT) | +------+------+-------------------------------------------------------+ | OUT | IN | Drive is Master, Slave is present | +------+------+-------------------------------------------------------+ | IN | OUT | Drive Slave | +------+------+-------------------------------------------------------+ | OUT | OUT | Drive is Master | +------+------+-------------------------------------------------------+ DRIVE EMULATES BOTH MASTER AND SLAVE Specifies that one 2210A drive can emulate both the Master drive (Drive 0) and the Slave drive (Drive 1). This option allows for existing host systems to utilize the full capacity of the drive. When the drive is configured as both the Master and the Slave, the Master's (Drive 0) capacity is set to: 1024 logical cylinders, 16 logical heads, and 63 logical sectors. This setting yields 528,482,304 bytes. The Slave's (Drive 1) capacity is set to the remaining storage on the disk drive. For this configuration, the recommended drive type setting in your computer's CMOS memory is as follows: Drive 0 Drive 1 Logical Cylinders: 1024 867 Logical Heads: 16 16 Logical Sectors: 63 63 Capacity (bytes): 528,482,304 447,455,232 When the drive is configured as a Master or as a Slave, the recommended drive type parameters are as follows: Logical Cylinders: 1891 Logical Heads: 16 Logical Sectors: 63 Capacity (bytes): 975,937,536 NOTE: The capacity of the 2210A drive may exceed the capacity that the host can access. This limitation stems from the communication link between the DOS and the BIOS. A typical limit is: 1024 cylinders, 16 heads, 63 sectors NOTE: If you have a machine with a BIOS that supports over 16 heads, you can set the drive to be a SLAVE or MASTER with one full partition. To do this, set the drive for: Logical Cylinders: 930 Logical Heads: 64 Logical Sectors: 32 Capacity (bytes): 975,175,680 DRIVE IS MASTER, SLAVE IS PRESENT Specifies the Master drive (Drive 0) when two 2210A drives are used in the system. The other drive is the Slave. DRIVE IS SLAVE Specifies the Slave drive (Drive 1) when two 2210A drives are used in the system. The other drive is the Master. DRIVE IS MASTER Specifies the Master drive (DRIVE 0) when one 2210A drive is used in a system. ---------------------------------------------------------------------- MICROPOLIS 2217A DISK DRIVE SPECIFICATIONS Model Number Unformatted Capacity: 2217A8- Total Mbytes -------------- 1896 ----------------- Disk Platters ----------------- 8 ----------------- Read/Write Heads ----------------- 15 ----------------- Cylinders -------------- 2372 ----------------- Bytes per track ----------- VARIABLE ----------------- Formatted Capacity Total Mbytes -------------- 1626 ----------------- Bytes per Sector ---------------- 512 ----------------- Sectors per Track ----------- VARIABLE ----------------- Performance Specifications Seek Time Track-to-Track 2 msec (including settling time) Average 10.0 msec Maximum 25 msec Average Rotational Latency 5.56 msec Rotational Speed 5400 rpm +/- 0.5% Data Transfer Rate at Interface Up to 5.0 Mbytes/sec Internal Data Rate 32 to 40 MHz MTBF 300,000 hours Positioner Fully balanced rotary voice coil Parking Automatic park and lock General Functional Specifications Interface AT/IDE Supports Full Common Command Set YES Mounting Plane Any orientation Power Requirements +12V +/-5% 0 .6A Avg (2.2A max during start-up) +5V +/-5% 0.85A avg Power dissipation, typical 11.5 Watts 7. Drive Options ____ _______________________ ________ | J2 | | J1 | | J3 | | |_|_______________________|_|________| | | | RESERVED | | | | | | | : : : : : | | | | | | W1 | | | W2 | | | \/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/ /\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\ | LED | |________||_______________________________| W1, W2 Jumpers (Master / Slave Selection) The interface allows up to two drives (a Master and one Slave) to be attached to the AT/IDE bus. The following table shows the configurations. W1 W2 Description +------+------+-------------------------------------------------------+ | IN | IN | Drive emulates *both* Master and Slave (DEFAULT) | +------+------+-------------------------------------------------------+ | OUT | IN | Drive is Master, Slave is present | +------+------+-------------------------------------------------------+ | IN | OUT | Drive Slave | +------+------+-------------------------------------------------------+ | OUT | OUT | Drive is Master | +------+------+-------------------------------------------------------+ DRIVE EMULATES BOTH MASTER AND SLAVE Specifies that one 2217A drive can emulate both the Master drive (Drive 0) and the Slave drive (Drive 1). This option allows for existing host systems to utilize the full capacity of the drive. When the drive is configured as both the Master and the Slave, the Master's (Drive 0) capacity is set to: 1024 logical cylinders, 16 logical heads, and 63 logical sectors. This setting yields 528,482,304 bytes. The Slave's (Drive 1) capacity is set to the remaining storage on the disk drive. For this configuration, the recommended drive type setting in your computer's CMOS memory is as follows: Drive 0 Drive 1 Logical Cylinders: 1024 2128 Logical Heads: 16 16 Logical Sectors: 63 63 Capacity (bytes): 528,482,304 1,098,252,288 When the drive is configured as a Master or as a Slave, the recommended drive type parameters are as follows: Logical Cylinders: 3152 Logical Heads: 16 Logical Sectors: 63 Capacity (bytes): 1,626,734,592 NOTE: The capacity of the 2217A drive may exceed the capacity that the host can access. This limitation stems from the communication link between the DOS and the BIOS. A typical limit is: 1024 cylinders, 16 heads, 63 sectors NOTE: If you have a machine with a BIOS that supports over 16 heads, you can set the drive to be a SLAVE or MASTER with one full partition. To do this, set the drive for: Logical Cylinders: 788 Logical Heads: 64 Logical Sectors: 63 Capacity (bytes): 1,601,316,864 DRIVE IS MASTER, SLAVE IS PRESENT Specifies the Master drive (Drive 0) when two 2217A drives are used in the system. The other drive is the Slave. DRIVE IS SLAVE Specifies the Slave drive (Drive 1) when two 2217A drives are used in the system. The other drive is the Master. DRIVE IS MASTER Specifies the Master drive (DRIVE 0) when one 2217A drive is used in a system. ----------------------------------------------------------------------